Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
| michka:research:microbial_fuel_cells:cardiff5 [2016-09-21 09:48] – michka | michka:research:microbial_fuel_cells:cardiff5 [2016-09-21 09:56] (current) – michka | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| =====MFCitizen @Cardiff===== | =====MFCitizen @Cardiff===== | ||
| - | **September 7th-9th, 2016** | + | **[[http:// |
| - | **[[http:// | + | |
| {{: | {{: | ||
| Line 181: | Line 180: | ||
| * sometimes, templates come up in large .zip files with components from a manufacturer, | * sometimes, templates come up in large .zip files with components from a manufacturer, | ||
| * open the template in Eagle, and check that it is the right one. | * open the template in Eagle, and check that it is the right one. | ||
| - | {{: | + | {{: |
| * if you are using, as we did, a fiber-glass support with a copper layer on top, keep in mind that were you cut, you are removing the copper, and therefore the electrical connexion. | * if you are using, as we did, a fiber-glass support with a copper layer on top, keep in mind that were you cut, you are removing the copper, and therefore the electrical connexion. | ||
| * export the G-code to Eagle’s plug-in connecting it to the CNC | * export the G-code to Eagle’s plug-in connecting it to the CNC | ||
| - | {{: | + | {{: |
| * beware that the G-code is defined in the right unit - metric or imperial system. | * beware that the G-code is defined in the right unit - metric or imperial system. | ||
| * make the CNC run | * make the CNC run | ||
| - | {{: | + | {{: |
| * this part of the process is quite technical, as the dimensions there are challenging Paul’s CNC sensitivity. Paul had to try out several times, and play with : | * this part of the process is quite technical, as the dimensions there are challenging Paul’s CNC sensitivity. Paul had to try out several times, and play with : | ||
| * the number of passes of the CNC on each cut | * the number of passes of the CNC on each cut | ||
| Line 196: | Line 195: | ||
| ===2.4 Building Shantaram et al.’s PHS=== | ===2.4 Building Shantaram et al.’s PHS=== | ||
| + | |||
| + | {{: | ||
| This was basically the same process as stated above, with a digression in updating Eagle to read the library files for the Maxim1797 layout, and getting compatibility issues with the CNC plug-in. | This was basically the same process as stated above, with a digression in updating Eagle to read the library files for the Maxim1797 layout, and getting compatibility issues with the CNC plug-in. | ||
| Line 204: | Line 205: | ||
| {{: | {{: | ||
| {{: | {{: | ||
| - | {{: | ||
| {{: | {{: | ||
| Line 223: | Line 223: | ||
| ===2.5 Beam robotics “Solar engine” PHS=== | ===2.5 Beam robotics “Solar engine” PHS=== | ||
| - | {{: | + | {{: |
| - | {{: | + | |
| When discussing about a lower-tech charge pump circuit, Paul mentionned the Beam robotics circuits, which are often made of basic through-hole off-the-shelf components, and are powered by renewables. | When discussing about a lower-tech charge pump circuit, Paul mentionned the Beam robotics circuits, which are often made of basic through-hole off-the-shelf components, and are powered by renewables. | ||
| Line 237: | Line 236: | ||
| Anyway, we prototyped and tested the circuit (replacing the motor by a LED), and it worked perfectly well. A 2200 uF proved to be way to small to really see the circuit effect on a LED. We replaced it by a 10 F supercapacitor, | Anyway, we prototyped and tested the circuit (replacing the motor by a LED), and it worked perfectly well. A 2200 uF proved to be way to small to really see the circuit effect on a LED. We replaced it by a 10 F supercapacitor, | ||
| + | |||
| + | {{: | ||
| ===2.6 Through-hole-components-based charge pump=== | ===2.6 Through-hole-components-based charge pump=== | ||
| Line 252: | Line 253: | ||
| ====2.7 Joule Thief PHS==== | ====2.7 Joule Thief PHS==== | ||
| - | {{: | + | {{: |
| - | {{: | + | |
| - | {{: | + | |
| ===2.7.1 Literature review=== | ===2.7.1 Literature review=== | ||
| Line 308: | Line 307: | ||
| ==2.7.2 First prototype and next steps== | ==2.7.2 First prototype and next steps== | ||
| + | |||
| + | {{: | ||
| While searching all the information mentionned above, we wanted to do a quick test with a basic JT design. | While searching all the information mentionned above, we wanted to do a quick test with a basic JT design. | ||
| Line 345: | Line 346: | ||
| ====3. Performance Tracking System==== | ====3. Performance Tracking System==== | ||
| - | {{: | + | {{: |
| ===3.1 Why INA219 current sensor ?=== | ===3.1 Why INA219 current sensor ?=== | ||
| Line 409: | Line 410: | ||
| ===4.1 Graphite electrode=== | ===4.1 Graphite electrode=== | ||
| - | {{: | + | {{: |
| - | {{: | + | |
| - | {{: | + | |
| - | {{: | + | |
| - | {{: | + | |
| Paul built a graphite electrode of out graphite rods we bought at The Works, an Arts & Crafts shop. | Paul built a graphite electrode of out graphite rods we bought at The Works, an Arts & Crafts shop. | ||
| + | |||
| + | {{: | ||
| He cut down the rods in smaller chunks, drilled them, and used an old bicycle stainless steel cable to assemble them like a collar. | He cut down the rods in smaller chunks, drilled them, and used an old bicycle stainless steel cable to assemble them like a collar. | ||
| + | |||
| + | {{: | ||
| + | {{: | ||
| Then, he tightened them up with a second bit of bicycle staineless steel cable (a choice of material advised by Johann, from the Flower Power pot project). | Then, he tightened them up with a second bit of bicycle staineless steel cable (a choice of material advised by Johann, from the Flower Power pot project). | ||
| + | |||
| + | {{: | ||
| A quick multimeter test showed that the overal resistance of the assembly was about 3 ohms. | A quick multimeter test showed that the overal resistance of the assembly was about 3 ohms. | ||
michka